Mr. Heater MH60CLP Instructions d'exploitation télécharger pdf (Page 6)



Forced Air Propane Construction Heater Operating Instructions and Owner’s Manual



1. The heater should be inspected before each use, and at least

annually by a qualified person.

2. Before each use, check the soft "O" ring seat at the bullnose

of the POL fitting. If the "O" ring is cut, scuffed, or otherwise

damaged, replace it with part number F273786.

3. Turn off the gas at the LP-gas supply cylinder(s) when the heater

is not in use.

4. When the heater is to be stored indoors, the connection

between the LP-gas supply cylinder(s) and the heater must

be disconnected and the cylinder(s) removed from the heater

and stored out of doors and in accordance with Chapter 5 of

the standard for Storage and Handling of Liquefied Petroleum

Gases ANSI/NFPA 58 and CSA B149.1, Natural Gas and Propane

Installation Code.

5. It is recommended that the internal battery be maintained on a

constant maintenance charge by leaving it plugged into a 120V

power source. If constant maintenance charging is not possible,

it is recommended that the battery be fully charged every 3

months.

6. The heater may be stored with the charger disconnected if all of

the following conditions are met.

•The battery is fully charged before storing. (Failure to store fully

charged will shorten battery life.)

•The average temperature of the storage location is below 50°

(10°C).

•Storage duration is less than 6 months.



A hazardous condition may result if a heater is used that has been

modified or is not functioning properly. When the heater is working

properly:

* The flame is contained within the heater.

* The flame is essentially blue with perhaps some yellow tipping.

* There is no strong disagreeable odor, eye burning or other

physical discomfort.

* There is no smoke or soot internal or external to the heater.

* There are no unplanned or unexplained shut downs of the

heater.

The parts lists and exploded view show the heater as it was

constructed. Do not use a heater which is different from that shown.

In this regard, use only the hose, regulator and cylinder connection

fitting (called a POL fitting) supplied with the heater. 

Match the color stripe on the hangtag attached to the hose assembly

with the color on the label located near the propane inlet fitting on

the heater. Do not use alternates. For this heater, the regulator must

be set as shown in "specifications". If there is any uncertainty about

the regulator setting, have it checked.

A heater which is not working right must be repaired, but only by a

trained, experienced service person.

In-warranty products will be repaired with no charge for either parts

or labor. Please include a brief statement indicating date, place of

purchase, the nature of the problem and proof of purchase.

Out-of-warrranty products will be repaired with a charge for parts,

labor and shipping.

WARNING

FIRE HAZARD—ALWAYS DISCONNECT THE HEATER FROM

THE POWER SUPPLY (WALL OUTLET) BEFORE REMOVING

THE POWER CORD FROM THE HEATER. UNDER CERTAIN

CONDITIONS, WITH THE HEATER PLUGGED INTO THE POWER

SUPPLY, THE EXPOSED CONNECTOR CAN BE SHORTED BY

FOREIGN MATERIAL AND MAY CAUSE A FIRE. FOREIGN

MATERIALS OF A CONDUCTIVE NATURE, SUCH AS, BUT NOT

LIMITED TO, STEEL WOOL, ALUMINUM FOIL, OR ANY BUILD-

UP OF METALLIC PARTICLES, SHOULD BE KEPT FROM THE

CONNECTOR. ALWAYS UNPLUG HEATER BEFORE ATTEMPTING

TO CLEAN.

HEATER OPERATION

START

1. The HERO heater is equipped with a blower fan switch, located

on the control panel of the heater. Press the on/off switch to

start the blower fan. Once the fan has been turned on, the

green LED light on the control panel will turn on solid, indicating

that the fan is operating. The blower fan must be turned on

before the gas/igniter valve is SLOWLY pressed to light the

heater.



cannot be depressed until after the fan has been started.

2. Open propane supply valve on propane tank slowly. Note: If not

opened slowly, excess-flow check valve on propane tank will stop

gas flow. If this happens, close propane supply valve and open

again slowly. Wait 15 seconds before Step 3.

3. After the blower fan has been started, SLOWLY depress the

orange gas/igniter valve button located on the control panel to

ignite the heater. If the heater fails to light, release the orange

button and repeat this step. Keep the valve depressed for 30-60

seconds, after burner lights, then release and the heater will

continue to operate. If the burner shuts off, wait 20 seconds and

repeat these steps.

NOTICE: This heater is equipped with a safety solenoid lockout

that prevents the gas valve being depressed until the heater

is turned on and the fan is operating. This system allows 30

seconds for ignition attempts. After 30 seconds the heater must

be reset for additional attempts. To reset, switch the on/off

switch to off and then back on.



When the heater detects a power source change (connect or

disconnect AC power while operating) it will automatically shut down.

After shut down, the "START" procedure will have to be used to

restart the heater.



This heater is equipped with a low battery voltage lockout

safety system that prevents operation if the battery voltage is too low.

STOP

1. Press the on/off switch to turn off the heater.

2. Turn off gas supply when heater is not in use.

1 2 3 4 5 6 7 8 9 10 11 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Mr. Heater MH60CLP Instructions d'exploitation Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Chauffages d'appoint Mr. Heater MH60CLP